• Eλληνικά
  • English
» Login
στείλτε VIBER τηλ.6944340728  Messenger   e-mail: 323582@gmail.com  
 
      
  
ζητήστε κωδικό
εισόδου
Ευχαριστούμε

Info: Your browser does not accept cookies. If you want to put products into your cart and purchase them you need to enable cookies.

SERVICE Sp problem Trouble arrow Sc Error +RESET problem arrow hp plotters 500, 450, T610 arrow hp Dj 1050c check printhead path (1) (2) help +



hp Dj 1050c check printhead path (1) (2) help +
 
Price per Unit (τεμ.): Offer a price you like

hp Dj 1050c check printhead path (1) (2)


 clean.....

 επισκευή Ελέγξτε τη διαδρομή της κεφαλής εκτύπωσης

DesignJet 1050 repair check printhead path - YouTube

Hewlett Packard 1050C - Check Print Path Error (2) - Part Two!

Re: HP DesignJet 1050c Check printhead path (2)

HP 1050C Plus "Switch power off Check printhead path ...

.......

  •  hp 1050c .... press Color key and On main switch ...to enter Service mode...

HP Designjet 5000 Series Printers -

TWI: Switch Power Off, Check Printhead Path

Performing service tests, service utilities and service calibrationsback to table of contents

  1. Turn the printer on.
  2. When the "READY" message is displayed on the front-panel, scroll to the Printer Setup Options icon and press ENTER.
  3. Using the Arrow keys, scroll to Utilities and press ENTER.
  4. Once inside the Utilities menu, press the Up Arrow key and the ENTER key simultaneously.
  5. Scroll to the necessary menu (Service Tests, Service Utilities, or Service Calibrations) and press ENTER.
  6. Once inside the appropriate menu, scroll to the needed test and press ENTER to start the test.

.........

 hp Dj 1050c clutch feed C6072-60151

 

.............

HP Designjet 1050C Belt Replacemnt & Calibration Video

2015-03-24 

 

check printhead path(1)

BELT was damadged, so I replace with new one... after power on ...gives the error ..

 Ph carriage moves a little L- R -L  and stops

sensor lights Red on enconder strip

 .... or  check strip enconder position out off ps path....

 

  • Switch Power Off. Check Printhead Path (1)

This warning appears whenever friction on the Scan-Axis is too high: the electrical current needed by the Scan-Axis Motor to move the Carriage is too high, so before burning the motor or the Main PCA, this warning appears.

 

  •  

2016-06-18 

...............

 hp 1050c error

 system error 0b0006

 

System Error:

0B0006

Problem

Description:

The Trailing Cable has been incorrectly connected OR the fuse in

the Electronics Module has been burned.

 

Corrective Action:

 

WARNING

Turn the Printer OFF and disconnect the trailing cable. Check that the ends of the Trailing Cable are flat and are not damaged or bent.

Reconnect the Trailing Cable correctly, making sure it is pushed in

firmly (Refer to the instructions on Page 8-39).

Power ON Printer and check if the Error Code disappears. If the Error Code

continues, replace the Electronics Module (Refer to the instructions

on Page 8-25)making sure you take care when you reconnect the trailing cable.

 

PLEASE TAKE CARE WHEN CONNECTING THE TRAILING CABLE TO THE ELECTRONICS MODULE. INCORRECT INSTALLATION WILL BURN THE FUSE IN

THE ELECTRONICS MODULE, CAUSING THE COMPLETE

REPLACEMENT OF THE ELECTRONICS MODULE.

......

003402:000001

 carriage moves 5cm to right + 1 cm to left and gives error by:

fuse F7?   cables, main PCA....

 

2016-07-27 

…………

Removal and Installation

8-27

HP DesignJets 1050C and 1055CM Printers Service Manual

Installation of the Electronics Module

WARNING

When reconnecting the Trailing Cable to the Electronics

Module, make sure you connect it correctly as follows:

1.

Start reconnecting the Trailing Cable from left to right (the longest

strip will be connected to the 1st clip from the right).

2.

Make sure you push the Trailing Cable in straight and not bent. Once

the Trailing Cable is inserted, you should hear an audible click.

3.

When the Trailing Cable is inserted correctly, the shaded part (as

shown below) will

not

be visible.

4.

Before powering ON the Printer, check the continuity (using a

tester) between the two points (as shown below).

n

If there is

continuity

between the two points, then the Trailing

Cable is installed

incorrectly.

Do

NOT

power ON the Printer

because you will burn an internal Electronics Module fuse.

Disconnect the Trailing Cable and reconnect again using the

above steps.

n

If there is

no continuity

between the two points, then it is

possible to power ON the Printer without burning the internal

Electronics Module fuse, but there is a possibility that you may

still get the System Error Code 0B0006, in which case you have

to reconnect the Trailing Cable using the above steps.

Check Continuity

between these 2 point

 

 

.........

 

Parts required (part numbers are subject to change)back to table of contents

 

Part description

Models - C6090A/V, C6091A/V

Models - C6095A/V, C6096A/V

Scan-Axis Motor (Required)

C6090-60328 / Q1251-60268

C6090-60328 / Q1251-60268

Carriage Belt (Required)

Q1251-60144

Q1253-60021

Carriage Assembly (Required)

C6090-60281

C6090-60281

Trailing Cable (Required)

C6090-60060

C6095-60184

Tensioner (Required)

C6090-60327

C6090-60327

Cutter (Required)

C6090-60094

C6090-60094

CE instructionsback to table of contents

 

.........

hp dj 1050 clutch feed assy   C6072-60151-C

Currently unavailable.
We don't know when or if this item will be back in stock.
  • C6072-60151 
 HP parts picture diagram for C6072-60151
..............
 

2016-06-18 


Availability

In Stock: 1

Usually ships in:

7d.gif


Last Updated: