hp Dj 1050c check printhead path (1) (2)
clean.....
επισκευή Ελέγξτε τη διαδρομή της κεφαλής εκτύπωσης
.......
- hp 1050c .... press Color key and On main switch ...to enter Service mode...
TWI: Switch Power Off, Check Printhead Path
Performing service tests, service utilities and service calibrations
- Turn the printer on.
- When the "READY" message is displayed on the front-panel, scroll to the Printer Setup Options icon and press ENTER.
- Using the Arrow keys, scroll to Utilities and press ENTER.
- Once inside the Utilities menu, press the Up Arrow key and the ENTER key simultaneously.
- Scroll to the necessary menu (Service Tests, Service Utilities, or Service Calibrations) and press ENTER.
- Once inside the appropriate menu, scroll to the needed test and press ENTER to start the test.
.........
hp Dj 1050c clutch feed C6072-60151
.............
HP Designjet 1050C Belt Replacemnt & Calibration Video
2015-03-24
check printhead path(1)
BELT was damadged, so I replace with new one... after power on ...gives the error ..
Ph carriage moves a little L- R -L and stops
sensor lights Red on enconder strip
.... or check strip enconder position out off ps path....
- Switch Power Off. Check Printhead Path (1)
This warning appears whenever friction on the Scan-Axis is too high: the electrical current needed by the Scan-Axis Motor to move the Carriage is too high, so before burning the motor or the Main PCA, this warning appears.
2016-06-18
...............
hp 1050c error
system error 0b0006
System Error:
0B0006
Problem
Description:
The Trailing Cable has been incorrectly connected OR the fuse in
the Electronics Module has been burned.
Corrective Action:
WARNING
Turn the Printer OFF and disconnect the trailing cable. Check that the ends of the Trailing Cable are flat and are not damaged or bent.
Reconnect the Trailing Cable correctly, making sure it is pushed in
firmly (Refer to the instructions on Page 8-39).
Power ON Printer and check if the Error Code disappears. If the Error Code
continues, replace the Electronics Module (Refer to the instructions
on Page 8-25)making sure you take care when you reconnect the trailing cable.
PLEASE TAKE CARE WHEN CONNECTING THE TRAILING CABLE TO THE ELECTRONICS MODULE. INCORRECT INSTALLATION WILL BURN THE FUSE IN
THE ELECTRONICS MODULE, CAUSING THE COMPLETE
REPLACEMENT OF THE ELECTRONICS MODULE.
......
003402:000001
carriage moves 5cm to right + 1 cm to left and gives error by:
fuse F7? cables, main PCA....
2016-07-27
…………
Removal and Installation
8-27
HP DesignJets 1050C and 1055CM Printers Service Manual
Installation of the Electronics Module
WARNING
When reconnecting the Trailing Cable to the Electronics
Module, make sure you connect it correctly as follows:
1.
Start reconnecting the Trailing Cable from left to right (the longest
strip will be connected to the 1st clip from the right).
2.
Make sure you push the Trailing Cable in straight and not bent. Once
the Trailing Cable is inserted, you should hear an audible click.
3.
When the Trailing Cable is inserted correctly, the shaded part (as
shown below) will
not
be visible.
4.
Before powering ON the Printer, check the continuity (using a
tester) between the two points (as shown below).
n
If there is
continuity
between the two points, then the Trailing
Cable is installed
incorrectly.
Do
NOT
power ON the Printer
because you will burn an internal Electronics Module fuse.
Disconnect the Trailing Cable and reconnect again using the
above steps.
n
If there is
no continuity
between the two points, then it is
possible to power ON the Printer without burning the internal
Electronics Module fuse, but there is a possibility that you may
still get the System Error Code 0B0006, in which case you have
to reconnect the Trailing Cable using the above steps.
Check Continuity
between these 2 point
.........
Parts required (part numbers are subject to change)
CE instructions
.........
hp dj 1050 clutch feed assy C6072-60151-C
Currently unavailable.
We don't know when or if this item will be back in stock.
2016-06-18