HP Designjet 500 800 Error Codes hp 500 IInitializing.... no code.... take outAc plug +Usb...On.... Ph fault... 2023.02 piter
hp 500 stops during initilizing.. . cant start up Paper Motor... fault ==change p. motor 2023.02 papad m
If your HP Designjet 500 plotter is giving you a error message please contact us for a free phone diagnostics. We can trouble shoot any Designjet error code and will provide you with a free quote for the parts needed to get your Designjet 500 running fast.
- OK pcl3 in 510plus with card. see these... Dnj 500 PCL3GUI 64-bit 6.08 2.4 MB Nov 14, 2012, and HP Dnj 500 and 510 HP-GL/2 and HP RTL 64-bit driver 7.10 2.8 MB Nov 14, 2012 ...ok
01.10 electronics module error hp-GL, Main Pca or short circuit, cables etc
System Error: 01:13 - Electronics Module failure
System Error: 02:10 - Carriage failure test moving with Upp+Enter +ON...
System Error: 02:13 - Carriage failure
System Error: 03:10 - Power Supply failure
System Error: 04:11 LAN - Card not detected
System Error: 05:10 Warning - Formatter not detected, electronics module error hp-GL(500ps)
-take it out and set the PCL3 Driver, HP Dnj 500 driver W8.1 for W10 wAutocad 2018 0.12pap
System Error: 05:10 Error - Formatter failure electronics module error hp-GL(500ps) -take it out and set the PCL3 Driver
System Error: 05:11 - Formatter Not Detected
System Error: 08:11 - Front Panel Not Detected
System Error: 11:11 - Trailing Cable Badly Connected, or need a new cables set...
System Error: 11:13 - Problem with setting the voltage of the Printheads
System Error: 12:11 - A short detected in the Carriage Assembly
System Error: 21:10 - Service Station failure, or broken cup in servStation, moving impossible, interconnect cable check after set a new belt...
foam or connector, carriage cables...., or full
System Error: 21:11 - Service Station cannot be detected or the Service Station is badly adjusted, conn.
System Error: 22:10 - Ink Supply Station failure test with service mode
System Error: 41:10 - Paper-Axis Motor failure test with service mode
System Error: 41:13 - Error in the Paper-Axis Motor Encoder quadrature
System Error: 42:10 - Scan-Axis Motor failure test with service mode
System Error: 43:10 - Vacuum Fan failure
System Error: 43:11 - Vacuum Fan not detected
System Error: 56:10 - Drive Roller Encoder Sensor error clean or replace ps or disk
System Error: 56:13 - Error in the Drive Roller Encoder Sensor quadrature.
System Error: 61:04 - Firmware Error
System Error: 61:05 - Error Processing Job. This Error Code only appears in HP DesignJets 800
Series, or in the HP DesignJet 500 and 510 Series with an HPGL/2 card installed,
when processing either a PostScript or HP-GL/2 file
System Error: 64:04 - Firmware Error (USB Port)
System Error: 71:04 - Problem allocating Memory. This Error Code only appears in
HP DesignJets 800 Series, or in the HP DesignJet 500 and 510 Series with an HP-GL/2 card installed.
System Error: 71:06 - Out of Memory problem hp500plus w hpGL 160mb Ram, w7 64bit, Drawing Out of memory Data lost but prints continous pdf's
System Error: 72:04 - Problem in the Scan-Axis (Firmware Error)
System Error: 73:04 - Servo Error
.........78:04 - tsurak joh
System Error: 79:04 - Firmware Error, check Ink supplies or PrintHeads, cables
System Error: 81:01 - Paper-Axis shutdown, Motor...or Encoder sensor test with service mode
System Error: 81:11 - Paper-Axis shutdown (during the Paper Advance test)
System Error: 85:10 - Paper-Axis Encoder error. The Drive Roller Encoder Sensor cannot find the zero position of the Encoder Disk
System Error: 86:01 - Carriage-Axis shutdown, Belt, or broken ink tubes assy, moving faulty...
clean - check Enconder Strip if it is..... broken carriage , or Service station parts...
System Error: 86:11 - Carriage-Axis shutdown, moving faulty...
System Error: 86:13 - Carriage-Axis shutdown (Firmware Error)
System Error: 87:13 - Unable to read the Carriage Encoder Sensor
System Error: 93:10 - Ink System startup failed
- Tags:
- HP designjet 800ps | Refurbished HP designjet 800ps | designjet 800ps large format | wide format 800ps | Designjet 800ps plotter parts | Designjet 800 800Ps 5:10 error
Re: HP Designjet 800ps - error code 11:11 on start-up
12-08-2010 08:18 AM
That is the trailing cable problem. I had that error before and fixed myself.
You can try the following :
Try to move the carriage box to the far left side
remove the middle cover ( remove screws on the back and lift it up )
Remove the grid plastic cover ( use a small screw drive and insert it to a small hole on the left side )
Pay close attention to the trailing cable where it enters the carriage box on the upper right corner.
Press down the cables to the sockets on circuit board.
Also make sure the ink cable enter the carriage box's corner correctly, it should clipped into the small hole and press down the trailing cable. I made a mistake on this step before and when printing and printer made noise
and after few days and 11:11 error again, so I learned a hard lesson.
Be patience and carefully. the troubles were on the trailling cables both ends. That is all. No big deal.
201@
Here‘s a driver HP Designjet 500 Printer series that correspond to your printer model:
- HP Designjet 500 24-in Roll Printer
- HP Designjet 500 42-in Roll Printer
- HP Designjet 500 Plus 24-in Roll Printer
- HP Designjet 500 Plus 42-in Roll Printer
- HP Designjet 500ps 24-in Roll Printer
- HP Designjet 500ps 42-in Roll Printer
- HP Designjet 500ps plus 24-in Printer
- HP Designjet 500ps plus 42-in Printer
HP DesignJet 500 24-in Roll Printer Driver
Operating System | Version | Size | Download |
HP Instant Printing application – Windows 10/XP/Vista/7/8/2012/8.1 (32/64-bit) | 3.6 | 29.6 MB | Download |
HP Designjet 500 and 510 HP-GL/2 and HP RTL 32-bit driver – Windows 7/XP/2003/Vista/2008/8 | 7.10 | 2.6 MB | Download |
HP DesignJet 500 PCL3GUI 32-bit Driver – Windows 7/XP/2003/Vista/2008/8 | 6.08 | 2.1 MB | Download |
DesignJet 500 PCL3GUI 64-bit Driver – Windows 7/2003/XP/Vista/2008 | 6.08 | 2.3 MB | Download |
HP Designjet 500 and 510 HP-GL/2 and HP RTL 64-bit driver – Windows 7/2003/XP/Vista/2008 | 7.10 | 2.7 MB | Download |
Lookup Pantone Tables for HP Designjet 500 and 800 Series – Windows ME/NT 4.0/2000/XP (32-bit) | N/A | 0.15 MB | Download |
HP Designjet 500, 510 and 800 Printer series Firmware Upgrade – Windows Vista/XP/2003 (32/64-bit) | A.04.02 | 28.5 MB | Download |
HP Designjet 500 and 800 ICC Profiles – Windows Vista/2000/XP/2003 (32-64-bit) Mac OS 9/Mac OS X/Mac OS X 10.5 | 1.0 | 1.4 MB | Download |
DJ800-500 HP Bond and Coated Paper – Windows Vista/2000/XP/2003 (32/64-bit) | 1.0 | 1.6 MB | Download |
HP Designjet 500, 510 and 800 Printer series Firmware Upgrade – Mac OS X/Mac OS X 10.5 | A.04.02 | 26.7 MB | Download |
Lookup Pantone Tables for HP Designjet 500 and 800 Series – Mac OS X | N/A | 0.12 MB | Download |
DJ800-500 HP Proofing Papers – Mac OS X | 1 | 3.1 MB | Download |
DJ800-500 HP Bond and Coated Paper – Mac OS X | 1 | 1.6 MB | Download |
HP Designjet Mac Raster Driver – Mac OS X 10.5/Mac OS X 10.6 | 4.4 | 171.9 MB | Download |
Mac HP Designjet Raster Driver – Mac OS X 10.6 | 27.0 | 181.8 MB | Download |
HP Designjet Mac Raster Driver – Mac OS X 10.7 | 4.4.3 | 179.6 MB | Download |
Mac HP Designjet Raster Driver – Mac OS X 10.7/10.8/10.9/10.10 | 30.0 | 183 MB | Download |
HP Designjet 500 and 800 HP-GL2 and HP RTL Driver – Windows 2000 | 6.15 | 1.9 MB | Download |
HP Designjet 500 Printer Raster Driver – Windows 2000 | 6.06 | 1.8 MB | Download |
DJ800-500 HP Proofing Papers – Windows 2000/XP/2003/Vista (32/64-bit) | 1.0 | 3 MB | Download |
HP Designjet 500 and 800 HP-GL/2 driver – Windows NT 4.0 | 6.11 | 1.8 MB | Download |
HP DesignJet Printer Driver for AutoCAD 13 and 14 – Windows NT 4.0 | 4.6 | 2.2 MB | Download |
Prior to installation, you should check the specifications used device that includes the type of printer and operating system that is used on your Pc and laptop.
If you have any questions, complaints and suggestions. Please let us know at admin@printerdriverseries.com
2017.09