Ricoh 1060 error, ready copying ready copying ready copying ready

 Ricoh copying...    2012-10-30

but no copy, no paper feed,

and error codes SC353, SC860..... no other code  //no feed-no copy.....

after 7.000.000 copies made...........

displays, without paper feeding /copying out..no . ADF wire  or connector, no HDD
trouble....???

After rebuilding + with bower cleaning, can make only 1 copy(good) and gives SC490 ....

.....SC495 recycling error

 495 D Toner recycling unit error
Encoder pulse does not change for
3 s after the main motor switches
on.
• Too much load on the drive mechanism
• Toner end sensor detective,

.......................................................

sc672  from HDD  for 2027 copier..... or no HDD installed.... Ricoh 2075  706@

.........

 4-31
Troubleshooting
SC No. Symptom Possible Cause
IEEE 1394 I/F error
Driver setting incorrect and cannot
be used by the 1394 I/F.
• 1394 I/F connection incorrect
• 1394 I/F board defective
• Controller board defective
851 B
USB driver is corrupted or has
become unstable and cannot be
used by the USB I/F.
• USB connection incorrect
• Controller board defective
860 B HDD startup error at main power on
• HDD is connected but a driver
error is detected.
• The driver does not respond with
the status of the HDD within 30
s.
• HDD is not initialized
• Level data is corrupted
• HDD is defective
861 B HDD re-try failure
At power on with the HDD detected,
power supply to the HDD is
interrupted, after the HDD is
awakened from the sleep mode, the
HDD is not ready within 30 s.
• Harness between HDD and board
disconnected, defective
• HDD power connector disconnected
• HDD defective
• Controller board defective
862 A Number of bad sectors exceeds allowed maximum
The number of bad sectors on the
HDD in the area for storing images
exceeds 101.
• Execute 5832 001 to format the HDD and
replace the bad sectors. HDD
replacement is recommended because
an HDD unit that generates bad sectors
is probably of poor quality and performs
poorly.
863 D HDD data read failure
The data written to the HDD cannot
be read normally, due to bad
sectors generated during operation.
• HDD defective
• Note: If the bad sectors are generated at
the image partition, the bad sector
information is written to NVRAM, and the
next time the HDD is accessed, these
bad sectors will not be accessed for
read/write operation.
864 D HDD data CRC error
During HDD operation, the HDD
cannot respond to an CRC error
query.
• Data transfer did not execute normally
while data was being written to the HDD.
865 D HDD access error
HDD responded to an error during
operation for a condition other than
those for SC863, 864.
• HDD defective.

 352 C ID sensor error 3
For 2 s during the ID sensor pattern
check, the ID sensor pattern edge
voltage is not 2.5V or the pattern
edge is not detected within 800 ms.
• ID sensor defective
• ID sensor harness disconnected
• ID sensor connector defective
• BCU defective
• Defect during ID sensor pattern writing
• Charge power pack defective
• ID sensor dirty
353 C ID sensor error 4
One of the following ID sensor
output voltages is detected at ID
sensor initialization.
• Vsg < 4.0V when the maximum
PWM input (255) is applied to the
ID sensor.
• Vsg ≥ 4.0V when the minimum
PWM input (0) is applied to the
ID sensor.
• ID sensor defective
• ID sensor harness disconnected
• ID sensor connector defective
• BCU defective
• Defect during ID sensor pattern writing
• Charge power pack defective
• ID sensor dirty
354 C ID sensor error 5
20 s after the start of automatic
adjustment, Vsg cannot be adjusted
to target (4.0 ± 0.2V).
• ID sensor defective
• ID sensor harness disconnected
• ID sensor connector defective
• BCU defective
• Defect during ID sensor pattern writing
• Charge power pack defective
• ID sensor dirty
355 C ID sensor pattern voltage error
Drum potential sensor output is out
of the target range (-100 - -400V)
when reading the drum voltage for
the ID sensor pattern.
• Drum potential sensor defective
• Drum potential sensor harness
disconnected
• Drum potential sensor connector
defective
• IOB defective
• Defect during ID sensor pattern writing
• Charge power pack defective
• Charge corona wire dirty

 ..............

2012-10-30 

Availability In Stock: 1 Usually ships in: