• Eλληνικά
  • English
» Login
στείλτε VIBER τηλ.6944340728  Messenger   e-mail: 323582@gmail.com  
 
      
  
ζητήστε κωδικό
εισόδου
Ευχαριστούμε

Info: Your browser does not accept cookies. If you want to put products into your cart and purchase them you need to enable cookies.

RESET error Codes + arrow Ricoh Aficio 1060 ERROR Sc545 & 541 Ricoh Aficio



Ricoh Aficio 1060 ERROR Sc545 & 541 Ricoh Aficio
 
Price per Unit (τεμ.): €49.00

 Ricoh Aficio 1060 ERROR  Sc545 & 541

RESET  as...  yellow 1 0 7  STOP  copy Sp...  off/on



SC510

• Tray lift motor defective or connector
disconnected
• Lift sensor defective or disconnected
• Pick-up solenoid defective or
disconnected
• Paper end sensor defective
B064 SERIES SERVICE MODE 30 June 2006
4-22
SC No. Symptom Possible Cause
515 B Tandem rear fence motor error
One of the conditions is detected:
• The rear fence does not reach
the return position within 10 s
after the rear fence motor
switches on, or does not return to
the HP.
• The HP sensor and return sensor
switch on at the same time.
• Rear fence motor defective or poor
connection
• Paper or other obstacle trapped between
tray and motor
• Motor mechanical overload
• Return sensor or HP sensor defective or
dirty
516 B Tandem side fence motor error
The side fences do not reach the
fully open or closed position within
2 seconds after the side fence
motor switches on.
• Side fence motor defective or poor
connection
• Motor mechanical overload
• Side fence positioning sensor defective
or dirty
520 D Duplex jogger motor error 1
When the jogger fence moves to
the home position, the jogger HP
sensor does not turn on even if the
jogger fence motor has moved the
jogger fence 153.5 mm.
• Paper or other obstacle has jammed
mechanism
• Sensor connector disconnected or
defective
• Sensor defective
521 D Duplex jogger motor error 2
When the jogger fence moves from
the home position, the jogger fence
HP sensor does not turn off even if
the jogger motor has moved the
jogger fence 153.5 mm.
• Paper or other obstacle has jammed
mechanism
• Sensor connector disconnected or
defective
• Sensor defective
541 A Fusing thermistor open
• The fusing temperature detected
by the thermistor is below 7°C for
35 seconds.
• The center thermistor (noncontact)
abnormal.
• Thermistor open
• Thermistor connector defective
• Thermistor damaged or warped
• Fusing temperature –15% less than the
standard input voltage
542 A Fusing temperature warm-up error
• After power on, or after closing
the front door, the hot roller does
not reach the 80°C control
temperature within 360 s.
• After the fusing lamp
temperature exceeds 80°C,
temperature does not change 2
degrees within 20 s.
• Fusing lamp disconnected
• Thermistor warped or installed incorrectly
• Thermostat operating
543 A Fusing lamp overheat error 1 (software)
• Central thermistor detected a
temperature of 230°C at the
center of the hot roller.
• End thermistor detected 220°C x
100 ms 5 times at the end of the
hot roller.
• PSU defective
• BCU defective
544 A Fusing lamp overheat error 1 (hardware)
The BCU detects an overheat error
even if the protection in the
software does not work.
• PSU defective
• BCU defective
30 June 2006 B064 SERIES SERVICE MODE
4-23
Troubleshooting
SC No. Symptom Possible Cause
545 A Fusing lamp overheat error 2
After hot roller reaches the warmup
temperature, the fusing lamps
continued full capacity output for 55
s without the hot roller rotating (for
a total of 45s).
• Fusing thermistor out of position
547 D Zero cross signal malfunction
One of the following conditions is
detected 10 times:
• When the main switch is on, the
frequency measured by the
number of zero cross signals for
500 ms is larger than 66Hz or
smaller than 45 Hz.
• The interval between one zero
cross signal and the next is 7.5
ms or shorter 3 times
consecutively for 500 ms.
• Noise on the ac power line
550 A Fusing Web End
Web end detected 5 times within
500 ms and web motor continues to
rotate 40 s. If web end is detected
for another 400 ms, then the SC is
logged.
• Web end (requires replacement)
• Web end sensor defective
Note: After replacing the web with a new
one, reset SP1902 001 to 0 to
release SC550.
590 D Toner collection motor error
The toner collection motor sensor
output does not change for 3
seconds while the toner collection
motor is on.
• Toner collection motor defective
• Motor drive defective
• Toner collection motor sensor connector
defective
• Motor overload
599 D 1-bin Exit Motor Error (should only occur in Japanese models)
The transport lock sensor output
does not change within 300 ms
after the motor switches on.
• Motor overload
• Motor drive defective

 

2012-12-14 


Availability

This product is currently not available.
Usually ships in:

on-order.gif

 


Last Updated: