Info: Your browser does not accept cookies. If you want to put products into your cart and purchase them you need to enable cookies.
RESET error Codes + Ricoh Aficio 1060 ERROR Sc545 & 541 Ricoh Aficio
|
Ricoh Aficio 1060 ERROR Sc545 & 541 RESET as... yellow 1 0 7 STOP copy Sp... off/on
SC510
• Tray lift motor defective or connector disconnected • Lift sensor defective or disconnected • Pick-up solenoid defective or disconnected • Paper end sensor defective B064 SERIES SERVICE MODE 30 June 2006 4-22 SC No. Symptom Possible Cause 515 B Tandem rear fence motor error One of the conditions is detected: • The rear fence does not reach the return position within 10 s after the rear fence motor switches on, or does not return to the HP. • The HP sensor and return sensor switch on at the same time. • Rear fence motor defective or poor connection • Paper or other obstacle trapped between tray and motor • Motor mechanical overload • Return sensor or HP sensor defective or dirty 516 B Tandem side fence motor error The side fences do not reach the fully open or closed position within 2 seconds after the side fence motor switches on. • Side fence motor defective or poor connection • Motor mechanical overload • Side fence positioning sensor defective or dirty 520 D Duplex jogger motor error 1 When the jogger fence moves to the home position, the jogger HP sensor does not turn on even if the jogger fence motor has moved the jogger fence 153.5 mm. • Paper or other obstacle has jammed mechanism • Sensor connector disconnected or defective • Sensor defective 521 D Duplex jogger motor error 2 When the jogger fence moves from the home position, the jogger fence HP sensor does not turn off even if the jogger motor has moved the jogger fence 153.5 mm. • Paper or other obstacle has jammed mechanism • Sensor connector disconnected or defective • Sensor defective 541 A Fusing thermistor open • The fusing temperature detected by the thermistor is below 7°C for 35 seconds. • The center thermistor (noncontact) abnormal. • Thermistor open • Thermistor connector defective • Thermistor damaged or warped • Fusing temperature –15% less than the standard input voltage 542 A Fusing temperature warm-up error • After power on, or after closing the front door, the hot roller does not reach the 80°C control temperature within 360 s. • After the fusing lamp temperature exceeds 80°C, temperature does not change 2 degrees within 20 s. • Fusing lamp disconnected • Thermistor warped or installed incorrectly • Thermostat operating 543 A Fusing lamp overheat error 1 (software) • Central thermistor detected a temperature of 230°C at the center of the hot roller. • End thermistor detected 220°C x 100 ms 5 times at the end of the hot roller. • PSU defective • BCU defective 544 A Fusing lamp overheat error 1 (hardware) The BCU detects an overheat error even if the protection in the software does not work. • PSU defective • BCU defective 30 June 2006 B064 SERIES SERVICE MODE 4-23 Troubleshooting SC No. Symptom Possible Cause 545 A Fusing lamp overheat error 2 After hot roller reaches the warmup temperature, the fusing lamps continued full capacity output for 55 s without the hot roller rotating (for a total of 45s). • Fusing thermistor out of position 547 D Zero cross signal malfunction One of the following conditions is detected 10 times: • When the main switch is on, the frequency measured by the number of zero cross signals for 500 ms is larger than 66Hz or smaller than 45 Hz. • The interval between one zero cross signal and the next is 7.5 ms or shorter 3 times consecutively for 500 ms. • Noise on the ac power line 550 A Fusing Web End Web end detected 5 times within 500 ms and web motor continues to rotate 40 s. If web end is detected for another 400 ms, then the SC is logged. • Web end (requires replacement) • Web end sensor defective Note: After replacing the web with a new one, reset SP1902 001 to 0 to release SC550. 590 D Toner collection motor error The toner collection motor sensor output does not change for 3 seconds while the toner collection motor is on. • Toner collection motor defective • Motor drive defective • Toner collection motor sensor connector defective • Motor overload 599 D 1-bin Exit Motor Error (should only occur in Japanese models) The transport lock sensor output does not change within 300 ms after the motor switches on. • Motor overload • Motor drive defective 2012-12-14
Availability This product is currently not available. Usually ships in:
|
|
Last Updated: