Scanner CIS W240 γκοφρετα
14, B1251649 Contact Image Sensor Unit w240 /A045
>> >>B2751648 OBSOLETE δεν διατιθεται καινουργιο...
ΓΙΩΡΓΟ ΚΑΛΗΜΕΡΑ ΕΧΩ ΕΝΑ RICOH MPW 3600 A0 ΤΟ ΟΠΟΙΟ
ΣΤΟ COPY ΒΓΑΖΕΙ ΜΑΥΡΗ ΜΑΥΡΗ ΓΡΑΜΜΗ ΚΑΙ ΠΙΣΤΕΥΩ ΟΤΙ ΕΙΝΑΙ ΠΡΟΒΛΗΜΑ ΣΤΑ CIS .
ΤΟ ΕΚΑΝΕ ΜΕΤΑ ΑΠΟ ΔΙΑΚΟΠΗ ΡΕΥΜΑΤΟΣ .ΕΙΧΕ ΠΕΣΕΙ ΚΑΙ Η ΑΣΦΑΛΕΙΑ ΤΗΣ ΜΗΧΑΝΗΣ
ΑΝ ΕΧΕΙΣ ΝΑ ΜΟΥ ΠΡΟΤΕΙΝΕΙΣ ΚΑΤΙ ΠΕΡΙΜΕΝΩ email ιμια Π.Κ. ΕΥΧΑΡΙΣΤΩ
2018-03-28
#2=100 #3=70+tax
...... print a test pattern...
Ricoh 240w parts in stock, used items in working condition
- βγαλτε το φωτοτυπια ( ενα σχεδιο γραμμικο),
- Σαρωστε το ιδιο, ( ενα σχεδιο γραμμικο),
- και εκτυπωστε (το ιδιο σαρωμενο εγγραφο)
Στειλτε και τα τεσσερα αρχεια να τα δω. ευχαριστω.
θελετε τεμαχιο απο τον σαρωτη
...πανω στο τζαμακι εχει 5 λευκα-γκοφρεττα CIS, οπως εδω φωτο,
το 2ο + 4ο εχουν μικρα γαντζακια αρ - δε, 1ο +3ο +5ο ομοια με μεγαλα γαντζακια αρ - δε
η κεφαλη εκτυπωσης?
εσωτερικα πανω απο το τυμπανο εχει 3 κεφαλες εκτυπωσης... printHeads OKI
................
SCANNER 13 / February 2004
3-16
3.2.4 CIS
Lift and lock the scanner unit. (☛ 3.1.7)
Original width sensor cover, original exit roller cover (☛ 3.1.10)
[A]: At the rear, open the CIS ribbon harness clamps (" x 11)
NOTE: Open only the harness clamps connected to the plate. Do not open the
clamps on the bottom of the CIS unit.
[B]: CIS unit (# x 5, ! x 4)
NOTE: Be sure to disconnect each ferrite core.
Reinstallation
After you replace the CIS, do the following procedure:
1. Read the values for SP4972 that are printed on the label attached to the CIS
replacement unit.
NOTE: The label is attached to replacement CIS units only.
2. Do SP4972 and input the 8 values.
3. Do SP2941 and print Pattern 11 to check the CIS.
4. Adjust if necessary. (☛3.11.2)
B125R110.WMF
B125R109.WMF
Rear View
[B]
[A]
13 February 2004 SCANNER
3-17
Replacement
Adjustment
5. Do SP4428 002 (Image Scan Adjustment Start) to adjust the standard white
level.
1) Go into SP mode 4428 002 and push Enter (#).
2) Push 1. The machine shows In Progress.
3) Put a stack of 5 sheets of A1 LEF paper on the original feed table. Use plain
white paper of a type used by the customer. The machine feeds the stack
part of the way into the scanner. After approximately 20 seconds, the
machine feeds stack through and out of the scanner. Then the display will
change to Finished.
4) Push Exit three times.
5) Switch the main power off, then back on.
6. Do SP4428 001 (Image Scan Adjustment Flag Display) to check that the
white level was adjusted.
2020-09-15