KONICA MINOLTA bizhub c35 ...αν θέλετε ανακατασκευής Α4 ZAHLER Admin Settings Password 92729*** Service call 3x Down arrow TROUBLE RESET Yes... off/on
SOLUTIONs FOR c35 Every time! before check ... take AC PLUG out for 2-3minutes ... And ON main Switch.... Toner Life press Supplies, ....consumables click Supplies...
Counter Read by explorer as preset ip 192.168.1.36 login as User
Waste Box ... .... enable.warning, select, 1up, Waste ...select to off
Network Setting IP. ZAHLER/Counter Admin set 12345678 select Ethernet select down IP setting
Admin 92729272 or 00000000 or 12345678, or Counter, Meter st 00 st 01
Set units Life 30k to Long 100k
Easy service Units Replace within 5 minutes w/o screwdriver!
Fuser or Unit replace ..only with 1-2 clips....
Service mode Zahler/Counter ...Meter, st 0 0 st 01 ...enter in Service, pass 1234* 9272
ID Card program, in ... copy menu
Scan Set to FTP, Shared folder...(settings...FTP18 ip192.168.1.18 Telia Anonymous) Start
CopyQuality setting, copy Settings Quality photo, Density Level, Auto/manual preset
Initilizing take out AC plug, or change Drum or Drums
- c0094 tsoxaki transfer assy or broken axis gear transfer
- c6790 optics
- c6791 optics assy or broken axis gear scanner
- poor quality, paper or bad transfer moving... check assy
- c9401 optics lamp o assy
- check scanner lock lever is belt or scanner assy unit
- calibrating is an optics scanner faulty
initializing or calibration and steady display. locked. take out All supplies and On Main switch... play and fixed ok
- no compact pdf, also delays at scanning ,,, >>>HDD out or faulty
- INCORRECT HDD...admin...menu lower HDD Format...ok
>>>mooore - 0F52, 53, 54 C M Y Toner sensors, Motor damadged RR R a capacitor 120μF 50V
- Display on but not touch, ... or delay at start
- not energy saver
- no Network connection off/on
- no yellow color on color print, Transfer belt Y roller klik broken...
- no toner, no chip, error chip, other model
- Scanner optics Lock clip, or optics Belt broken, or clean Lamp
- Replenish paper...
- c0094 IDC sensor at Tansfer belt not open by Gear clutch Rdoor, clean 1 clutch tsoxaki
- C9401 TROUBLE... DELAY start on Remains KONICA Logo, Calibrating, not Panel press...DOOR Lock switch optics,
- Konica c35 c 0094 IDC machine is dead transfer tsoxaki or axis broken
- c6790, c6792clean lens +Oil motor ... or ..or optics Belt broken
- ***error 6790...=optics lamp goes off during initilizing test, CN103 or Lamp board faulty
- red magenta printig quality
- initializing... 10 λεπτα εκτος πριζας, βαζω πριζα , κ Ανοιχτη πορτα εμπρος... μετα ανοιγεις διακοπτη, κλεινεις πορτα.
- toners +chip lost.... change ALL toners at once
Scanning with the machine, press SCAN to Folder FTP18 + START, smart Ftp... - Scan to e-mail... help Scan setup +
Scanning with the machine To add an additional e-mail address, to a specified address (e-mail address, FTP address or SMB address). >> === Raise the doc feeder when you press start to make a copy does the bright lite come on???? Try this procedure if code come back have tech come to replace the bright light under the big glass 1. Turn OFF the main power switch. 2. Turn main power switch ON while pressing the Utility/Counter key. 3. Touch [Trouble Reset]. 4. Check to make sure that [OK] is displayed and the it has been reset. 5. After turning off the main power switch, turn it on again more than 10 seconds after and check if the machine starts correctly.
Code 0094 Description 2nd image transfer pressure / retraction failure R door clutch • The IDC sensor does not come into the condition where the level detection is available (retracted position = IDC sensor shutter is open) within a given period of time after the 2nd transfer release solenoid has turned ON. • The IDC sensor does not come into the condition where the level detection is not available (pressed position = IDC sensor shutter is closed) within a given period of time after the 2nd transfer release solenoid has turned ON. c0096 .... Description 1st image transfer pressure / retraction failure • The 1st transfer release sensor is not activated (retracted position) within a given period of time after the 1st transfer release solenoid has turned ON. • The 1st transfer release sensor is not deactivated (pressed position) within a given period of time after the 1st transfer release solenoid has turned ON. c0300 polygon c0500 fuser ............... You can. You have to remove the fuser, and replace the counter reset fuse that is soldered into the wiring harness, then re-install the fuser. 10 minute job but not a one I would recommend unless you know the machine pretty well. Depending on your location and service options I would try to find a local independant repair person who can do this for you. I reset 20 to 30 of these fusers per year. Note you can also reset your transfer belt unit as well as your Imaging Units as well. Good Luck and Thank You for using Fixya. WheatlandServices Re: Bizhub C35 Transfer belt reset 1. Turn ON the power switch. NOTE: • Make sure that the USB cable, (the network cable, and the fax cable) are not connected to the machine. 2. From the Menu, select [Service Mode] → [Supplies] → [Consumables Replace] → [Transfer Belt Unit] and execute this function to reset the transfer belt unit counter value. 3. From the Menu, select [Admin Setting] → [Printer Setting] → [Quality Settings] → [Gradation Adjust] → [AIDC Process] and execute this function. 4. Connect the USB cable, (the network cable, and the fax cable) to the machine. for some reason every person who's ever worked on C25/C35 always confuses 0096 (first transfer pressure retraction) with 0094 (second transfer pressure retraction) Re: Bizhub C35 Transfer belt reset new or old, lubricate the sliding rails and cam lobes at friction areas on each side of the belt to prevent the damage to the 1st transfer pressure retraction drive (0096) ensure its reassembled correctly before installation. once damaged its game over, its a preventative measure not a fix. 2019-05-31 - c 6790 change lamp > c 9401 edo cl+oil again .....after many tests ok.
- c 6792 mbi cl +oil but 6790 some times come again ...
- check scanner lever praxi ok+belt new ok
- c 6790 foro dm cl + oil ok.
- check scanner lever ats set a new belt and ok.
- c 0094 Transfer IDC open shutter + clean check clutch +M2 with open door...other assy
- Camarato tsoxaki Protyp=all assy change
- who is next?
Konica Bizhub c35 DRUM CHIP K BLACK IU EUR 2018-08-08
Availability This product is currently not available.
|
|